Challenger Dyno Video

514 hp at the wheels. Big thanks to Bob Kurgan Motorsports for the tune.....

240sx SR20 Turbo Down Pipe

2.5" Custom Turbo Down Pipe for right hand drive 240sx

Custom 650cfm Holley for Patch

Milled Choke Tower

Dominator Dual Inlet Bowls

Notched Float w/ Jet Extensions

Carb is for Patch @ Hardcore Metalworks 327ci Small Block Ford / 5 Speed Street/Strip Project.

650 Mechanical Secondaries, Milled Choke Horn, Notched Float w/ Jet Extensions etc. etc....
                                        Carb got the full bag of tricks on it.

We rebuild, modify & tune all types for carbs and have a large selection of Holley cores in stock. Custom Powder Coating is available.

                                                   Give us call for a quote.

66 GMC

more handmade patch panels

More rust repair.
I have it killed........
A little grinding and patch a hole in the roof where an antenna use to be and we will be back to Blast Technology for a touch up. Then off to paint. I can't wait to see this baby in yellow & white.

77 LUV Update

2000 4.3 EFI swap

Custom mexican blanket seat upholstery by Tim Wallace Sr.

Tim & I picked it up from the exhaust shop today. Big shout out to Justin Palmer for doing a killer job on the exhaust.
We will be finishing up a few things tommorrow. ie. fan wiring, fixing leaking intake & etc etc.
Turkey Rod run here we come.........

66 GMC

Before

Home made patch cleco'd in place ready for welding

Mark's 66 GMC

Sealed both bed sides with self-etching primer

Ready for body work

A couple of custom patch panels

Drivers side completely welded and ground smooth

Passenger side welded and ground smooth

Just a few small places left on the outside to fix and all the rust will be gone.

How to Build Custom Spark Plug Wires

#1 Route wires.
I like using Taylor Cable  looms. 

Tools needed
spark plug wire crimpers, needle nose pliers, side cutters and WD40

clip a connector on cap
cut wire 3/4" longer than needed 

insert wire into crimper/stripper leaving 3/4" sticking out

wire should look like this after stripping

fold inner wire back

place connector over wire, making sure inner wire is at the top of connector.
slightly squeeze connetor on wire to keep it in place

insert into crimper, making sure connector in properly located

this is what it will look like crimped

install wire on cap and repeat 7 more times

spray WD40 into boot

insert needle nose pliers into boot

work the pliers in & out while twisting the boot a few times.
you will be able to feel when ready.

push connector into boot and repeat 7 more times

Your finished. Now grab a cold drink, sit back and enjoy not having ugly plug wires.

QCS does Late Model Muscle

CTS-V in for a few small things..

Shop full of New School Muscle Cars.

77 Chevy Luv 4.3 Swap

Flaked Steelies, Skinny Whites & Bullet Lugnuts

Custom Hardlines

1977 Chevy Luv with 2000 S-10 4.3 & 5 Speed swap for my painter Tim Wallace.  More pics soon......

2010 SRT8 Challenger Upgrades v2.0

Old Exhaust

About 6 months ago we did a MagnaCharger, Eibach Pro-Kit and Tint. Now its time for round 2.
Kooks long tubes, Cat delete, Corsa Exhaust, 90mm Arrington Throttle Body & Carbon Fiber cold air intake, 90mm MagnaCharger inlet, and a billet fuel hat w/ (2) 255lhr Walbro fuel pumps. We are shooting for around 700hp. This thing is gonna be NASTY!!!!!

78 Scottsdale 350 Engine Build

New A/C Lines

We finished the 78 Scottsdale today. Runs great!! Tons of Low End Torque....

1978 Scottsdale Engine Build

28,000 mile gem

 The man that owns it said it has no power. Queen City Speed / Eric Evans Racing Engines is going to fix that.

New short block

350ci, Vortec Heads, QCS/EERE Stage 1 camshaft, Hi Rise Qjet intake.

Before